{"product_id":"real-oak-pre-glued-veneer-edging-tape-22mm-50m","title":"Real Oak Pre-Glued Veneer Edging Tape 22mm x 50m","description":"\u003cp\u003eReal oak veneer edging tape, 22mm wide on a 50m roll, gives cut edges of oak boards, shelving panels and worktops a clean, timber-matched finish. The pre-applied hot-melt adhesive bonds with a domestic iron or edge bander, making it a practical choice for both trade and DIY cabinet work.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaterial\u003c\/td\u003e\n\u003ctd\u003eReal oak veneer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdhesive\u003c\/td\u003e\n\u003ctd\u003ePre-applied hot-melt (iron-on)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWidth\u003c\/td\u003e\n\u003ctd\u003e22mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRoll Length\u003c\/td\u003e\n\u003ctd\u003e50m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSuitable Substrates\u003c\/td\u003e\n\u003ctd\u003eMDF, chipboard, solid timber\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eWhat it's used for\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEdging oak-faced MDF and chipboard shelving to hide the substrate core\u003c\/li\u003e\n\u003cli\u003eFinishing the exposed edges of oak worktops and kitchen cabinet panels\u003c\/li\u003e\n\u003cli\u003eMatching veneer edges on flat-pack and bespoke furniture builds\u003c\/li\u003e\n\u003cli\u003eTidying cut edges on oak plywood where a neat face is required\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitting and handling\u003c\/h2\u003e\u003cp\u003eBefore applying, allow the edging tape to reach room temperature if it has been stored in a cold environment, as a chilled roll can cause the adhesive to bond unevenly. Set a domestic iron to a medium-high setting, press the tape firmly along the edge, and work in short sections to keep the adhesive active while you apply pressure. Once cool, trim any overhang flush using a sharp edge trimmer or chisel plane, then lightly sand with 180-grit paper for a tidy, paint- or oil-ready finish.\u003c\/p\u003e\u003ch2\u003eFAQ\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eWill this edging tape work with a standard household iron?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eYes. A domestic iron set to a medium-high heat activates the hot-melt adhesive reliably. Use a dry setting rather than steam, and apply firm, even pressure as you move along the tape. A small offcut of timber makes a useful pressing block to keep the tape flat while the glue sets.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow do I trim the tape flush without splitting the veneer?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA purpose-made edge trimmer gives the cleanest result and is widely available from woodworking suppliers. Alternatively, a very sharp chisel held flat to the face will pare the overhang back without tearing. Always work from the ends inward to avoid lifting the corners of the tape.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs 22mm wide enough for standard 18mm board?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eYes. The 22mm width gives 2mm of overhang on each face of an 18mm panel, which is the correct amount to allow for trimming flush. It also suits 15mm and 16mm sheet materials with slightly more overhang to trim back.\u003c\/p\u003e\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"Will this edging tape work with a standard household iron?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes. A domestic iron set to a medium-high heat activates the hot-melt adhesive reliably. Use a dry setting rather than steam, and apply firm, even pressure as you move along the tape. A small offcut of timber makes a useful pressing block to keep the tape flat while the glue sets.\"}},{\"@type\":\"Question\",\"name\":\"How do I trim the tape flush without splitting the veneer?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"A purpose-made edge trimmer gives the cleanest result and is widely available from woodworking suppliers. Alternatively, a very sharp chisel held flat to the face will pare the overhang back without tearing. Always work from the ends inward to avoid lifting the corners of the tape.\"}},{\"@type\":\"Question\",\"name\":\"Is 22mm wide enough for standard 18mm board?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes. The 22mm width gives 2mm of overhang on each face of an 18mm panel, which is the correct amount to allow for trimming flush. It also suits 15mm and 16mm sheet materials with slightly more overhang to trim back.\"}}]}\u003c\/script\u003e\u003cp\u003eFor the sheet materials this edging tape is designed to finish, browse our \u003ca href=\"\/collections\/oak-mouldings\"\u003eoak mouldings collection\u003c\/a\u003e at Nottage Timber Merchants. We supply trade and retail customers across Bridgend and South Wales, with next-day delivery available to many local postcodes. Contact us for bulk roll pricing.\u003c\/p\u003e","brand":"Nottage Timber Merchants","offers":[{"title":"Default Title","offer_id":52924561293649,"sku":null,"price":40.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0994\/1467\/1697\/files\/oakedging.jpg?v=1769616590","url":"https:\/\/www.timberonline.co.uk\/products\/real-oak-pre-glued-veneer-edging-tape-22mm-50m","provider":"Nottage Timber Merchants","version":"1.0","type":"link"}